D 10:4L combines 1000 W of flexible power with latest Lake DSP, Dante digital audio networking and advanced system integrity monitoring.
The D 10:4L is based on the same foundation of robust, high-power amplifier technologies as our renowned PLM Series an amplifier platform with a proven record of reliability and sonic performance on the worlds most grueling concert tours and in high-profile, large-scale installations.
With the D 10:4L, those same core technologies have been updated and refocused to provide the ultimate solution for the most demanding digitally networked installed sound applications in stadia, arenas, theme parks, performing arts centers, racecourses and other large commercial sound installations.
In addition to legendary Lab.gruppen reliability and sonic excellence, the D Series incorporates newly refined outputs stage technologies along with installation-targeted hardware and software features that optimize amplifier system design and configuration. Together, these new technologies allow systems integrators to minimize both initial equipment costs and end users long-term energy consumption.
- Rational Power Management (RPM) True flexibility in allocating total available power output across channel count for most efficient use of system inventory
- Any channel capable of being significantly scaled up for driving high power elements (e.g. subwoofers)
- Lake processing Classic/linear-phase/FIR speaker processing platform with 4 throughputs
- Input with multitude of automatic redundancy
- 4 Lake class analog inputs with Iso-Float ground isolation
- 4 AES inputs
- 8 Dual Redundant Dante inputs
- 4 Lake class analog inputs with Iso-Float ground isolation
- 4 AES inputs
- 8 Dual Redundant Dante inputs
- Integration potential with 3rd party matrix systems including BSS, Q-SYS and MediaMatrix via purpose developed middleware
- CAFÉ (Configuring Amplifiers For the Environment) Software incorporating ESP (Equipment Specification Predictor) for design, system planning and equipment planning, installation and commissioning.
- Regulated Switch-Mode Power Supply (R.SMP)
- Under-voltage Limiting (UVL) for continued operation despite severe voltage drops
- Best-in-class Power Factor Correction (PFC) with Current Draw Modelling
- Proven and reliable IDEEA Class D Output Stage with direct drive 70 and V constant voltage systems as well as low impedance
- Dedicated on-board surveillance & load monitoring system
- Redundant audio inputs and onboard system surveillance for mission-critical Voice Alarm applications (PA/VA)
- Detachable Phoenix plug-in audio connectors for audio I/O
General
- Processing / Network Lake / Dante
- Number of amplifier channels 4
- Total burst power all channels (share among channels with RPM) 1000 W
Max output power (all channels driven)1
- 2 ohms 250 W
- 2.67 ohms 250 W
- 4 ohms 250 W
- 8 ohms 250 W
- 16 ohms 250 W
- Hi-Z 25 V 250 W
- Hi-Z 70 V 250 W
- Hi-Z 100 V 175 W
Max output power single channel (all models)1
- 2 ohms 850 W
- 2.67 ohms 1000 W
- 4 ohms 1000 W
- 8 ohms 1000 W
- 16 ohms 600 W
- Hi-Z 25 V 500 W
- Hi-Z 70 V 1000 W
- Hi-Z 100 V 700 W
Amplifier output modules (all models, all channels)
- Peak output voltage 142 Vpk
- Max output current 30 Apk
- Rational Power Management (RPM) Share Total burst power of the product freely among channels. Any channel can scale up to the single channel max power
- Default voltage limitation (can be lifted with RPM configuration) 63 Vpk
- Protection features Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection
Audio Performance (Amplifier platform with digital input)
- THD + N 20 Hz - 20 kHz for 1 W < 0.05 %
- Amplifier gain Digital configurable amplifier gain 22 - 44 dB
- Pilot tone generation and analysis Yes
- Channel separation (Crosstalk) at 1 kHz > 70 dB
- Temperature control Temperature regulated fans (front-to-rear airflow) and show must go on limitation (ATL, PTL)
- Internal Sample Rate / Data path 96 kHz / 32 bit floating point
- Product propagation delay AES 96 kHz / analog input 1.61 / 1.68 ms
Lake processing
- Loudspeaker processing Up to 4 modules of Classic/linear-phase/FIR crossover, EQ, delay, LimiterMax - peak and RMS limiters
- System tuning Group control with Raised Cosine MESA EG asymmetric filters
- Input redundancy / Matrix Automatic 4 level input redundancy / 4 input mixers
- System integration Comprehensive 3rd party protocol over UDP Ethernet
Dante Audio Network
- Dante I/O 8 x 8
- Network topology / redundancy Flexible topology / Supports daisy-chained and Dual redundant networks
- Sample Rates / Transport 48, 96 kHz / Uni + Multicast
- Network latency 0.25, 0.5, 1.0, 2.0, 5.0 ms
AES Inputs
- Inputs 4 AES inputs
- Supported sample rates / resolution 44.1, 48, 88.2, 96, 176.4, 192 kHz / up to 24 bits
- Sample rate conversion THD+N 20 Hz - 20 kHz unweighted 0.00003 %
Analog Inputs
- Inputs 4 high quality inputs with Iso-Float ground isolation
- Maximum input / digital reference +26 dBu / +21 dBu
- Sampling rate / Resolution 96 kHz / 24 bit
- Input impedance balanced / unbalanced 20 / 10 kOhm
- THD+N (typical at 1 kHz unweighted) 0.00022 %
- THD+N (typical at 20 Hz and 20 kHz unweighted) 0.00033 %
Back panel Interface
- Analog inputs 4 x Terminal block connectors analog input with +, - and ground
- AES inputs 4 x Terminal block connectors analog input with +, - and ground
- Output connectors 4 x 2 pole Terminal block connectors rated at 1000 V / 41 A (exceeding amplifier capacity)
- Can take up to 8 mm2 (8.2 AWG) cables
- Ethernet Ports 2 x EtherCon RJ45 Lake Controller, Dante controller and/or DLM (3rd party protocol)
- Detachable mains cord Detachable locking 3-pin IEC rated at 250 V / 16 A
Front-panel user interface
- System status indication 3 x tri-color LED. FRAME, TEMP, PSU for device status indication
- Channel status indication 3 x tri-color LED per channel. Status indication separated for channel LOAD, AMP, SIGNAL status
- Mute Per channel touch button for MUTE control and tri-color LED for indication
- Power Touch button for ON/STANDBY control and tri-color LED for power state indication
- Select Touch button and LED for bidirectional device software select functionality
Mains Power
- Nominal voltage 100 - 240 Volt AC 50 - 60 Hz
- Operating voltage 70 - 265 V AC 45 - 66 Hz
- Mains wall plug Selectable on order
- CEE 7/7 Schuko 230 V / 16 A,
- NEMA 5-15 125 V / 15 A,
- BS1363-A 250 V / 13 A,
- IA16A3 250 V / 16 A,
- AU/NZ 250 V / 10 A,
- JP 125 V / 15 A,
- CPCS-CCC 250 V / 10 A
Power supply features
- Soft start / Inrush power Yes
- Power factor correction > 0.98 for mains power > 300 W
- Regulated switch mode power supply (R.SMPS) Yes
- Breaker Emulation Limiter (BEL) No
- BEL max current threshold Fixed 8 A
- Power Average Limiter (PAL) Yes
- Under Voltage Limiter (UVL) Yes
- Mains undervoltage and overvoltage protection and mains glitch tolerance Yes
Dimensions
- Rack rail to rear panel W: 483 mm (19), H: 44 mm (1 U), D: 425 mm (16.7)
- Overall depth front-rear support D: 463 mm
Weight
- Weight 7.8 kg (17.1 lbs)
- Finish
- Finish Black painted steel chassis with grey painted steel front with detachable grille
Approvals
- Approvals CE, ETL (ANSI/UL, CSA), PSE, RCM, BIS, CCC
Notes
1. Lab.gruppen burst power (1 kHz, 25 ms burst power @ 150 BPM, 12 dB Crest factor)
|